Materials, Industrial, and Manufacturing Engineering Research Advances 2 [Minkštas viršelis]

Preface
Chapter 1: Materials Engineering, Chemical Technologies and Materials
Processing
An Introduction to Lightweight, Energy Saving, Environment Friendly Magnesium
Based Nanocomposites: Materials of Upcoming Generation
Comparison of Three-Parameter Weibull Statistical Analysis of the Flexural
Strength of Dense and Porous Sintered Clay
Influence of Nano-Polyaniline Contents on Mechanical Properties of Crosslink
Recycled Polypropylene Polyaniline
TGO Formation with NiCoCrAlYTa Bond Coat Deposition Using APS and HVOF
Method
Alteration by Cerium Element on Primary and Eutectic Mg2Si Phases in
Al-20%Mg2Si In Situ Composite
Oxidation of Pure Aluminium Granules during In Situ Melting
Effect of Silver Nanoparticles in Silicalite-1 Zeolite on Antireflection and
Antibacterial Performances
Improvement of Hydrophilic Stability of Diamond-Like Carbon Films by O2/CF4
Plasma Post-Treatment
An Improvement of Photoanode Performance for Enhanced Efficiency in
Dye-Sensitized Solar Cell
Effect of Ingredient Loading on Vulcanization Characteristics of a Natural
Rubber Compound
Effect of Ingredient Loading on Water Transport Properties of a Vulcanized
Natural Rubber Compound
Effects of Electron Beam on Structure and Physical Properties of Natural
Colorless Topaz
Effect of Ingredient Loading on Surface Migration of Additives in a
Surfactant-Loaded Natural Rubber Vulcanizate
Characterisation of Moisture Absorption Effects on the Strength of Composite
Materials
Modeling Interlaminar Shear Crack-Jump Phenomenon in Fiber-Reinforced Polymer
Composites
Effect of the Gel Coat Composition on the Tensile Strength for Glass Fibre
Reinforced Polyester Composites
UV LED Curing Formulation for Polyacrylamide Hydrogels
Mechanical Behavior Analysis of Apus Bamboo (Gygantochloa sp) Thin Plate
Composite due to Adhesive Joint and Water Absorption Using Experimental and
Finite Element Method
Analysis of Bending Loads on Bamboo-Balsa and Bamboo-Polypropylene Honeycomb
Composite Sandwiches
Numerical and Experimental Analysis of Flexural Properties of Bamboo Tali
Laminate Composite
Studies on Effect of Zinc Oxide (ZnO) Nanostructures Morphology by
Modification of Sol-Gel Solution
Morphological Effect of Composite Coated SUS430 Steel during Thermal
Oxidation Process
Dry Sliding Wear Behavior of A356-ZrO2 Metal Matrix Composite
Interlaminar Damage Behavior of CFRP Composite Laminates under Cyclic Shear
Loading Conditions
Hydrothermal Synthesis Effect on Growth of Zinc Oxide Structure
Pulsed Current Electrodeposition of Mn-Cu Alloys on SUS 430 Substrate as
Coating Material for SOFC Interconnect Application
A Study on the Effect of Binder Content for Pore Property of Fe Foam Using
Slurry Coating Method
Investigation of Deposition Parameters Dependence on Sputtered Cu2ZnSnSe4
Thin Films Properties
Solution-Processable Field-Effect Transistor Behavior of -Conjugated
Oligothiophene
Parameter Design for Hardness of Metal Filled Epoxy Matrix
The Influence of Punch Angle on the Spring Back during V-Bending of Medium
Carbon Steel
Interaction of Metal and Slag in Continuous Casting Mold
Mathematical Modeling of Heat Losses in Steelmaking Ladles
Study of Heat Dissipation Generated in Tool Designed for Friction Stir
Welding Process (FSW)
Development of Aluminum Anodizing Process by the Power Supply Using Pulse
Width Rectifying Method
Thermal Response of Activated Charcoal Modified Investment Casting Moulds
A Study on Different Welding Processes of IN718 for Elevated Temperature
Application
A Study on Post Weld Heat Treatment of Friction Stir Welded Al2195 Blank for
Spin Forming
Mechanical Properties of Shielded Metal Arc Welded Low Carbon Steel: Effect
of Butt Joint Type and Uncapping of Excess Weldment
Effects of Salinity on Nanosilica Applications in Altering Limestone Rock
Wettability for Enhanced Oil Recovery
The Effectiveness of Cationic and Polymer Inhibitors on Shale
Improved Coefficient of Friction Using Different Types of Lubricants in
Drilling Operation
Chapter 2: Materials and Technologies in Environmental Engineering, Bio- and
Green Production
Cellulose Nanowhiskers Reinforced Green Nanocomposites: Some Recent
Development
Mechanical and Thermal Properties of Rubber Toughened Poly(Lactic Acid)
Mechanical Behavior of Composite Multilayered Basalt/E-Glass/Epoxy Pipe under
Internal Pressure
Effect of Colorant on Tensile Strength and Carbonyl Index of
Oxo-Biodegradable Low-Density Polyethylene Films during Thermal Aging
Sorption Kinetics of Pro-Oxidant-Loaded PE Plastic Bags in Aqueous Media
Effect of Filter Aids on Pressure Drop and Permeability of Two Different
Filter Media
Novel Hydrophilic Chitosan and Sago Based Membranes for Pervaporation of
Organic-Water Mixtures
Highly Response and Sensitive Copper Sensors Based on Chitosan Films
Overview on Mechanical-Chemical Ionic Liquid Pretreatment Study on
BioethanolBased Lignocellulosics Biomass
Characterization of Nanosilica of Tapioca Peel as Adsorbent for Biomethane
Storage System
Tensile and Morphological Properties of Hybrid
Montmorillonite/Microcrystalline Cellulose Filled Polylactic Acid Composites:
Effect of Filler Ratio
Effects of Pre-Treatment Conditions on Black Tilapia Fish Scales for Gelatin
Extraction
Biopolymeric Adsorbent for the Removal of Methylene Blue: Characterizations,
Equilibrium Isotherms and Kinetic Studies
Effect of Solvent on Adhesion Property of Glass Fiber Recycled by Superheated
Steam
Recycling Technique of Carbon Fiber Laminate Using Hydrolysis Near Critical
Region
Preparation of Cellulose Nanocrystal Aerogel from Wastepaper through
Freeze-Drying Technique
Effect of Fluidization Number on the Combustion of Empty Fruit Bunch in a
Fluidized Bed
Determination of Volatile Organic Compounds (VOCs) at Selected Pump Stations
in Skudai, Johor Bahru
Carbon Dioxide Removal by Using Absorption Process with 5M Aqueous Solution
of 2-(Methylamino)Ethanol
A Theoretical Performance of MR-DeDuster as a Fine Dust Emission Control
System
Particulate Emission from Biomass Fuel Combustion
An Investigation of Carbon Dioxide Sequestration on AmineModified Kenaf:
Adsorption Isotherm Study
Compatibility Issue Related to the Use of Biodiesel with Automotive
Materials
Microwave Assisted Pyrolysis of Rice Husk in the Presence of Eco Friendly
Microwave Absorber in Producing Bio-Oil
Chapter 3: Materials and Technologies in Construction
Cathodic Protection Effect of Reinforced Concrete Beam Specimens with Zinc
Sacrificial Anode in Marine Environment
The Experimental Measurement on the Throwing Power of Sacrificial Anode
Cathodic Protection for Concrete Piles in Natural Sea Water
Assessment of the Elastic Stress of 304 Stainless Steel Using Half-Cell
Potential Measurement
Influence of Ion Irradiated Recycled Polyethylene on Physical Properties of
Bituminous Binder
Utilization of Variable Resistor for Improvement of Impressed Current
Cathodic Protection System on Reinforced Concrete Structures
Fresh Properties of Self-Compacting Concrete Integrating Coal Bottom Ash as a
Replacement of Fine Aggregates
Effect of External Environment on the Properties of Selected Plasters
Determination of Salt Transport Properties of Sandstone: A Combined
Experimental/Computational Approach
A Study on the Structural Analysis of Jacket Substructure Related to Offshore
Wind Power Environment
Chapter 4: Materials and Technologies for Biomedical Application
Surface Characterization of Biomimetic Hydroxyapatite-Silver Functionalized
on Polydopamine Film
Effect of Sintering Temperature on the Mechanical Properties of
Nanostructured Ceria-Zirconia Prepared by Colloidal Process
New Solvent System for the Fabrication of Polyvinyl Alcohol Gelatin
Nanofibers via Electrospinning
Composite of Poly Lactid Co-Glycolic Acid (PLGA)-Collagen Coated by Chitosan
as Candidate of Hollow Fiber Small Diameter Vascular Graft
Investigation of Gamma Radiation on Hydroxyapatite Synthesized from Chicken
Eggshell by ESR Spectroscopy
Preparation and Characteristic of Hydroxyapatite Synthesized from Cuttlefish
Bone by Precipitation Method
The Effect of Silane on the Biomechanical Properties of PEEK/HA Composite
Design of Above-Knee Prosthesis: A Finite Element Stress Analysis
Porous Magnesium Scaffolds for Bone Implant Applications: A Review
Effects of Alkaline Treatment on Corrosion Behavior of Biodegradable
Magnesium
Effect of Heat Treatment on Surface Morphology of Titanium
Characterisation and In Vitro Bioactivity of UV-Treated Anodised Titanium
Anodic Oxidation of Titanium in Acetic Acid for Biomedical Application
Effect of UV Light Treatment Condition on Apatite Formation of Anodised
Titanium
Effect of UV Wavelength on Apatite Formation of Anodised Titanium
Analysis on Compressibility of Dental Amalgam Using Nanomaterial Zinc Oxide
(ZnO)
Effect of Calcination on the Properties of Hydroxyapatite from Tilapia Fish
Bones
Optimization and Characterization of Anatase Formed on Anodized Titanium in
Sulfuric Acid
Electrophoretic Deposition of Hydroxyapatite Coatings on AZ31: The Effect of
Nanoparticle Multiple Coating Approach
Effect of Processing Parameters and Heating Techniques on the Extraction
Yield of Eurycomalongifolia (Tongkat Ali)
A Novel Approach of Using SMA Wires Actuated Stewart Platform for Continuous
Passive Motion (CPM) of Ankle Rehabilitation Therapy
Behaviour of Acrylonitrile Butadiene Styrene (ABS) during Dewaxing Process
for Investment Casting of Proximal Humerus Implant
Microstructure and Properties of Forged CoCrMo Alloy for Load Bearing
Application
Chapter 5: Technological Equipments and Machines
Condition Monitoring of a Gear-Box Using Wear Particle Analysis Technique
Case Study on Reliability of Automotive Painting Shop Robots
Design of a High Accuracy 3-Axis Coordinate Measuring Machine Working on the
Shop Floor
Flutter Analysis of Functionally Graded Panel Based on Neutral Surface
Effect of Refrigerant on the Exergy Loss and Performance in Air Conditioner
Using Ejector as Expansion Device
Sensor Based on the Resonance Frequency for Detecting Overfilling in a
Pressing Apparatus
A Review of Multiple Edge Detection in Road Lane Detection Using Improved
Hough Transform
Road Safety Outcome Model among Commercial Bus
Modeling of Square Channel Reactor for Optimum Length Prediction
Enhancing Air Conditioning Performance Using TiO2 Nanoparticles in Compressor
Lubricant
Performance Comparison of Automotive Air Conditioner Using Various
Refrigerants
A Study on Dynamic Motion and Wave Power in Multi-Connected
Float-Counterweight Type of Wave Energy Converter
Peristaltic Micropump with Multi-Electrodes Using Electrostatic Force
Dynamic Strength Analysis for Mooring Design of Ship
Improvement of Containment Spray Heat Exchanger in Structure Analysis
Bio-Mechanism Response of Mimosa Pudica against External Stimulation
Analysis on the Degradation Characteristics of 2G High-Tc Superconducting
Wires in Accordance with Electrical Breakdown Voltage
Chapter 6: Industrial Engineering
Applying Game Theory to Competitive Production-Inventory Models with Vendor's
Imperfect Production Processes and the Condition of Buyer's Exemption from
Inspection
Level of Learning from Occupational Safety Accidents: Current Status in
Malaysia
Using AHP Multiple Criteria Decision Making Approach for Selecting a Type of
Industrial Plant at Risk on Fire
A Survey Instrument Design to Determine the Success Factors in Implementing
the End-of-Life Vehicles (ELVs) Management System in Malaysia
Safety Assessment Model for Coastal Passenger Vessel in the Perspective of
Compatibility of Life Jacket with the Coastal Passenger Vessel
New Product Pricing Using Fuzzy Logic Type-2
Future Trend Analysis on the Design and Performance of Solar-Powered Electric
Unmanned Aerial Vehicles
Review of Solar and Battery Power System Development for Solar-Powered
Electric Unmanned Aerial Vehicles