Advanced Materials and Application II [Minkštas viršelis]

Preface
Chapter 1: Metallurgical and Metalworking Technologies
Study on Factors which Make CBN Insert can Turn S45C Steel Have Surface
Roughness Less than Ra 0.4
Weldability of Similar and Different Metallic Materials
Computer Simulation and Analysis of the Parameters of the Drawing Process of
Thin Wire from the Alloy Pd-5Ni
Study of the Influence of Conditions of Combined Casting and
Rolling-Extruding and Two-Stage Annealing on the Structure and Properties of
Semi-Finished Electrical Products from an AlZr System Alloy
Computer Modeling and Analysis of the Energy-Power Process Parameters of the
Combined Machining of Alloys Al-Mg System
Investigation of Side-Dam Plate in Single-Wheel Caster for Casting Rods
Forming of Small Projection on Roll-Cast A356 Strip by Cold Rolling and Small
Groove on PET Plate Using A356 Die
600 mm-Wide Strip Casting Using Single Roll Caster Equipped with Scraper
Effect of Latent Heat of Aluminum Alloys on Bonding between Strips in Clad
Strip Cast by a Twin-Roll Caster
Chapter 2: Functional Ceramics and Fiber Composites
Mechanical Properties of PP/clay Nanocomposites Prepared from Masterbatch:
Effect of Nanoclay Loadings and Re-Processing
Influence of Sintering Temperature on Physical and Mechanical Properties of
Hydroxyapatite-Calcium Titanate Composite
Physical and Mechanical Properties of Bi0.5(Na0.81K0.19)0.5TiO3 Ceramic
Modified by KNbO3
An Analysis of Air Permeability of Cotton-Fibre-Based Socks
Examining Moisture Management Property of Socks
Mechanical and Rheological Properties of High Density Polyethylene Reinforced
Polyvinyl Alcohol Fiber Composites
Nanomaterial Production by Arc Discharge Sputtering of Silicon-Graphite and
Silica-Graphite Composite Anodes
Corrosion Behaviors of Reinforcing Steel in Concrete with Various Moisture
Contents
Chapter 3: Chemical Technologies in Environmental Engineering, Bioindustry
and Energy Production
Predictive Study of Combustion Temperature of Liquefied Petroleum Gas (LPG)
on the Spherical Packed-Bed Porous Burner
The Influence of Stainless Steel Mesh Porous Burner on Drying Kinetics of
Nile Tilapia
Green Synthesis of Iron Oxide Nanoparticles for Lead Removal from Aqueous
Solutions
Microwave Assisted Extraction (MAE) Process of Tannin from Mangrove
Propagules Waste as Natural Dye for Coloring Batik tulis
"Green" Bleaching Process of Sugar Palm (Arenga pinnata) Flour by Using
Sodium Salt and Ozone Technology
Fundamentals and Applications of Red Light-Emitting Diodes (LEDs) In Vitro
Plant Growth on Tomato Lycopersicon esculentum Mill
Production of Microsphere Polystyrene Using Solution Enhanced Dispersion by
CO2 Supercritical Fluids (SEDS)
Chapter 4: Materials and Technologies in Construction
Geometric Analysis of a Modular, Deployable and Reusable Structure
Study on Service Life of OPC and HPC in Marine Environment
Confinement Shear Effect in Fiber Composites
Original Experimental Campaign of Indentation Instrumented on Aggregates of
Non-Hazardous Waste Incineration Bottom Ash to Study the Heterogeneity of
their Rigidity
Chapter 5: Mechanical Properties and Durability of Structural Materials
Failure on Bearing Cooler Coils Connector of Hydroelectric Power Plant
Buckling Analysis of Variable Stiffness Composite Cylindrical Shells Based on
Hermite Curves
Elastoplastic Equilibrium of a Hollow Thick-Walled Radially Inhomogeneous
Ball
Stresses Analysis of Hypocycloidal Gear Transmissions