Advanced Materials and Engineering Materials VIII [Minkštas viršelis]

Preface
Chapter 1: Composites
Preparation and Properties of Tea Polyphenol Modified Graphene Oxide/Epoxy
Resin Composites
Two-Stage Sintering of Alumina-Y-TZP (Al2O3/Y-TZP) Composites
Pressing and Bonding Strength of Metal Matrix Composite
Influence of Molding Pressure on Properties of Al2O3- Al Composite Materials
Sintered via Vacuum Sintering Method
Kinetic Processes in Polydisperse Systems: Experience of Practical
Approximation
Chapter 2: Nanomaterials and Nanofabrication
Synthesis of Diamond-Like Structures by Method of Mechanochemical Treatment
of Nano-Carbon Materials (Taunit)
Optical and Electrical Properties of Diamond-Like Carbon Thin Film with
Deposition by ECR-CVD System
Highly Increased Flow-Induced Voltage Generation on Hybrid Membranes of
Monolayer Graphene and Single-Walled Carbon Nanotubes
Effect of Reaction Time on Surface Nano-Structure of TiN Oxide Nanofilm by
Hydrothermal Method
Toughened Poly(Trimethylene Terephthalate) by Melt Compounding with
Functionalized Graphene Oxide Nanocomposites
Controlled Hydrothermal Synthesis of K2Ti6O13 Nanowires and their
Photo-Electronic Response
Electrochemical Degradation of p-Nitrophenol on Cu Nanowires and Nanocubes
Photoelectric Response Difference between KTaO3/ Au and K2Ta2O6/Au
Nanocrystals Resulting from Potassium Tantalate Structure
Preparation and Characterization of In Situ Nanocomposites of Graphene
Nanosheets/Polyurethane
Crystalline Morphology and Crystallization Behavior of Poly(Trimethylene
Terephthalate)/Functionalized Graphene Oxide Nanocomposites Prepared by Melt
Compounding
Microstructure Analysis and Preparation of Graphene Reinforced Aluminum
Matrix Composites
Analysis of Electroluminescence Application on Display
Preparation and Characterization of 3-Glycidoxypropyltrimethoxysilane
Functionalized Graphene Oxide
Chapter 3: Properties of Steel and Alloys, Processing Technologies and
Manufacturing Processes
Low Cycle Fatigue Life Evaluation According to Temperature and Orientation in
Nickel-Base Superalloy
Effect of Frequency to Ultrasonic Vibration-Assisted Wire-EDM
Deformation Analysis of TC4 Titanium Alloy Shell Material
Cr12MoV Die Repair Experiment Based on Laser Cladding with Wire
Effect of Citric Acid on Cerium Conversion Coating of Hot-Dip Galvanized
Steel
Subsurface Stress Distribution and Failure of PPS Thrust Bearings under
Rolling Contact Fatigue in Water
Study on the High Temperature Creep Behavior of 30Cr25Ni20 Heat-Resistant
Steel
Effect of Different Hole-Making Technology on Fatigue Properties of
Directionally Solidified Alloy IC10
Control of Microstructure and Properties of Welded Joints of Heavy Structures
of Low Alloy High Strength Steels
Effects of Mixed Mode Loading Conditions on Fatigue Crack Growth Rate
Fundamental Research on Gasification Dephosphorization with Coke Powder
Reducing Converter Molten Slag
Experiments and Regression Analysis of Grinding Hardened Layer Depth Based on
Transverse Feed
Throughput Estimation Model of Cluster Tool in Semiconductor Manufacturing
An Intelligent Optimization System for PIM Process
Formation of Feed-Direction Burr in Axial Vibration Drilling
Main Features of High Speed Machining Chucks and their Selection
Failure Observation of 3D-Printed Thrust Bearing Specimens with Inner Defects
in Water Conditions
Welding Repair of High Chromium Cast Iron Defects
Research on Base Welding Technology of Alkaline Welding Rod with Arc Method
New Low Alloy High Strength Steel Welding Procedure Evaluation
Study on Welding Technology of Low Alloy High Strength Steel
Study on Fatigue Life of Straight Hole Plate of Directionally Solidified
Alloy IC10
Study on Particle Modified ABS in 3D Printing
Effect of Different Aging System on Microstructure and Mechanical Properties
of X2A66 Alloy
Optimization of Precipitation Phase Type and Mechanical Properties of X2A66
Alloy by Pre-Deformation Treatment
Study on Fatigue Properties of Copper Alloy Netting Structure
Chapter 4: Measurements and Modeling of Materials Properties and Materials
Behavior
Evaluation of Wickability of Quick Dry Inner Wear
A Study of Wickability of Gauze Products for Infant
Synthesis and Clay Anti-Swelling Properties of Diethyl Dodecyl Allyl Ammonium
Chloride
Microstructure Investigation of He+- Implanted and Post-Implantation-Annealed
4H-SiC
Thermal Management of a Li-Ion Battery for Electric Vehicles Using PCM and
Water-Cooling Board
Observation of Tribological Fatigue Fracture on PEEK Shaft with Artificial
Defect under One-Point Rolling Contact by Using 2.5D Layer Method
Multilayered Elastic Medium under Axisymmetric Loading and Surface Energy
Effect of Aspect Ratio on Horizontal Field Magnetoresistance
Observation of Crack Growth Behavior of 400m Cracks in 4.762mm Silicon
Nitride Balls under Cyclic Compressive Load
Effects of CeO2 Addition on Slip - Cast Yttria Tetragonal Zirconia
Polycrystals Toughened Alumina (ZTA)
Chapter 5: Materials for Biomedical Application
Antibacterial Properties among Different Concentration of Bioactive Glasses
Comparison of Three Commercial Latex and Non-Latex Orthodontic Elastic Bands
Chemical Constituents of the Aerial Parts of Scoparia Dulcis and Anti-Cancer,
Anti-Inflammatory Activities
Preparation, Characterization and Hemostatic Properties of Chitosan
Caffeates
Comparison of Mechanical Properties of Plain and Reversed Curve
Nickel-Titanium Archwires
Shear Bond Strength of Experimental Light-Cured Orthodontic Adhesives
Chapter 6: Materials and Technologies for Construction
Effect of Shrinkage Reducing Admixture on Shrinkage and Crack Properties of
Cement Based Materials
Water Resistance Modification of Magnesium Oxychloride Cement with
H3PO4/Na2O·xSiO2·nH2O
Correlation between Unconfined Compressive Strength and Penetration Index
Obtained from DCP Tests for Cemented Lateritic Soils
A Model for Bond Strength in Presence of Corrosion in Concrete
Effect of High Temperature Process on Microstructure and Properties of
Industrial Steel Slag Cement
Experimental Study on Permanent Deformation of Fine Sandy Subgrade Filling in
Coastal Region
Rebar Anchor Plate Research and Application
Evaluation on Sulfuric Acid Resistance of Concrete Protected by Biomimetic
Coating Mortar
Axial Behavior of Columns Strengthened with Seismic RC Jacket Section
Chapter 7: Materials and Technologies for Chemical Production and Processing
Synthesis of Cerium Phosphate White Pigments from Cerium Oxalate
Desorption of Mercury Complex from Fe-Modified Montmorillonite Adsorbent
Membrane
Ni0.75Fe0.25 Coated Tubular GDC Anode for Cathode-Supported IT-SOFC with High
Anode Porosity
Congo Red Dye Removal Using Ca-Al Layered Double Hydroxide: Kinetics and
Equilibrium
Effects of Extraction Conditions on Total Phenolic Content and Total
Flavonoid Content of Roselle (Hibiscus sabdariffa L.) Extracts
Response Surface Methodology Optimization for Extraction of Natural
Anthocyanins from Vietnamese Carissa arandas L. Fruit
Microfluidic Chip Injection Photo Solidification Molding Study on Reaction
Kinetics
Characterization and Photocatalytic Activity of Microspheres ZnO by
Hydrothermal Method
Synthesis of New Phosphate and the Evaluation as Scale Inhibitor in Oilfield
Modification of Ligustrum vulgare Leaves Extract as Eco-Friendly Corrosion
Inhibitors in Oil Fields
Study on Source Analysis of the Cation in Produced Water from Sulige Gas
Field and Anti-Scaling Measures
Preparation and Evaluation of Phosphate Scale Inhibitor for Oilfield Produced
Water
Catalytic Cracking of Oleic Acid over Zeolites
Effect of Compatibilization on the Melt Properties of Mixed Waste Plastics
Effect of Extraction Process on Extraction Yeild, Total Polyphenol Content
and Antioxidant Activity of Jasminum Subtriplinerve