This special edition is devoted to studying the properties of the semi-solid casting of non-ferrous alloys and corresponding metal matrix composites and will be helpful to metallurgists and engineers from mechanical engineering.
Preface
Chapter 1: Materials Development and Characterization
Variation of Semi-Solid Microstructure and Mechanical Properties of
Mg98.5Ni0.5Y1.0 Alloy with Solidification Pressure
Heat-Treatment Characteristics and Structure-Property Relationships of
Thixomolded AZ91 and Ultralight LAZ771 Magnesium Alloys
Fatigue Properties of Thixoformed Al-6wt%Si-2.5wt%Cu
Comparison of Solidification Microstructure Evolution of Al-10Si and Recycled
Aluminium Beverage Can Strips Made in a Strip Caster
Characterisation of Residual Stresses of Rheocast Al Alloy
Influence of Reinforcement Particle Parameters on the Homogeneity of Particle
Distribution in Semi-Solid Formed Aluminium Matrix Composites
Mechanical and Microstructural Investigations on a Symmetric Mould Processed
with Semi-Solid Aluminum RheoMetalTM: Analysis of the As-Cast Proprieties
A Comparative Study on Microstructure, Mechanical Property, and Electrical
Conductivity of Al-7Si-0.6Mg Alloy Produced by High Pressure Die Casting and
Semisolid Die Casting
A Comparison of Microstructure and Casting Defects of Rheocasting and
Thixocasting Al-Si-Mg Alloy
Effect of Mn Addition on Microstructure, Mechanical Properties and Die
Soldering of Rheocasting Al-7Si-0.3Mg Alloys
Abrasive Wear Properties Evaluation of the Thixoformed A380/NbC Composite
Preliminary Investigation on the Use of Recycled A356 Alloy for Semi-Solid
Processing
Semi-Solid Casting of AlN Reinforced Mg-Matrix Composites and their
Thermophysical Properties
Development of High Strength and High Thermal Conductivity Semi-Solid
Magnesium Alloy by Thixomolding Process
Rheological Behaviour of Secondary AlSi7Mg Alloy for Semi-Solid Processing
Effect of Ingate Length on Microstructure and Properties of Semi-Solid
Squeeze Casting CuSn10P1 Alloy
Microstructure Evolution during Cooling Slope Rheoprocessing of Novel
Al-15Mg2Si-4.5Si Composite
Evolution of Microstructure and Mechanical Properties of the Rheo-Diecast
Mg-12Gd-3Y-1Zn-0.4Zr Alloy during Heat Treatment
Chapter 2: Rheology, Modelling and Numerical Analysis
Rheological Behavior in the Semisolid State of Al-Si-Cu Alloys Produced by
ECAP
Numerical Simulations of the Squeeze Flow of Thixotropic Semisolid Slurries
Semi-Solid Deformation Behavior, Flow Stress Prediction and Deformed
Microstructure of GH3536 Superalloy
On the Possibility of Replacing Scheil-Gulliver Modeling with Machine
Learning and Neural Network Models
Rheological Modeling of 7075 Aluminum Alloy Semi-Solid Slurry and its
Application in the Simulation of SEED Rheocasting Process
CALPHAD Optimization of the Composition of EN AC-46000 Secondary Alloys for
Semi-Solid Casting Processes
Comparison of Rheological Models to Simulate Die Filling Process of A356
Semisolid Alloy
Thixomolding of Magnesium - Efficient Process Industrialization by Combining
a Digital Twin and Systematic Casting Trials
Quality Control of Semi-Solid Die Casting by Filling Pressure Based on
Machine Learning Method
A Molecular Dynamics Study of Nucleation and Grain Growth of Novel
Al-15Mg2Si-4.5Si Composite during Rapid Cooling Based Semi Solid Slurry
Preparation
